On the Impact of GNSS Receiver Settings on the Estimation of Codephase Center Corrections

verfasst von: Yannick Breva, Johannes Kröger, Tobias Kersten, Steffen Schön
Abstract: The role of codephase center corrections (CPC), also known as group delay variations (GDV), becomes more important nowadays, e.g. in navigation applications or ambiguity resolution. CPC are antenna dependent delays of the received codephase. They are varying with the angle of arrival of the signal at the GNSS antenna, i.e. with azimuth and elevation. CPC can be determined with a robot in the field with a similar approach as used for phase center corrections (PCC) for carrierphase measurements. The big challenge in the estimation of reliable CPC pattern is to deal with relatively noisy codephase observations compared to the correction magnitude. A better repeatability can be reached by reducing the overall codephase noise. One possibility to do this is to understand and improve the tracking loops of the receiver, especially the loop filters, within the calibration process. Due to highly dynamic stress caused by the fast robot motion, a perfect tracking of the GNSS signals is challenging. In this paper, a detailed look on the impact of different loop filter settings, like the noise bandwidth, the filter order or the use of an aided or unaided delay lock loop, on the time differenced single differences is done. To this end, an antenna calibration experiment was carried out, where, in addition to the hardware receivers, the IFEN Sx3 software receiver was used. The software receiver allows to change the settings in post-processing. The experiment shows, that the noise of the observations can be reduced by decreasing the noise bandwidth, but pattern information can be lost by using a bandwidth, which is too small. The trade-off between a small bandwidth and consequently less overall noise and the signal dynamics, caused by the fast robot motion, must be chosen carefully. At the end, an improvement in the pattern repeatability from 99.2 mm, using a hardware receiver, to 65.6 mm, using a software receiver with carefully chosen parameters, can be achieved.
Organisationseinheit(en): Institut für Erdmessung
Typ: Beitrag in Buch/Sammelwerk
Seiten: 101-108
Anzahl der Seiten: 8
Publikationsdatum: 2024
Publikationsstatus: Veröffentlicht
Peer-reviewed: Ja
ASJC Scopus Sachgebiete: Allgemeiner Maschinenbau, Angewandte Mathematik, Computer in den Geowissenschaften, Geophysik
Fachgebiet (basierend auf ÖFOS 2012): Navigationssysteme, Mathematische Modellierung, Satellitengeodäsie
Elektronische Version(en): https://doi.org/10.1007/1345_2023_206 (Zugang: Geschlossen)
: Details im Forschungsportal „Research@Leibniz University“

BibTeX

@inbook{2c2474cf40e5450fa18a5d443e74bd1c,
title = "On the Impact of GNSS Receiver Settings on the Estimation of Codephase Center Corrections",
abstract = "The role of codephase center corrections (CPC), also known as group delay variations (GDV), becomes more important nowadays, e.g. in navigation applications or ambiguity resolution. CPC are antenna dependent delays of the received codephase. They are varying with the angle of arrival of the signal at the GNSS antenna, i.e. with azimuth and elevation. CPC can be determined with a robot in the field with a similar approach as used for phase center corrections (PCC) for carrierphase measurements. The big challenge in the estimation of reliable CPC pattern is to deal with relatively noisy codephase observations compared to the correction magnitude. A better repeatability can be reached by reducing the overall codephase noise. One possibility to do this is to understand and improve the tracking loops of the receiver, especially the loop filters, within the calibration process. Due to highly dynamic stress caused by the fast robot motion, a perfect tracking of the GNSS signals is challenging. In this paper, a detailed look on the impact of different loop filter settings, like the noise bandwidth, the filter order or the use of an aided or unaided delay lock loop, on the time differenced single differences is done. To this end, an antenna calibration experiment was carried out, where, in addition to the hardware receivers, the IFEN Sx3 software receiver was used. The software receiver allows to change the settings in post-processing. The experiment shows, that the noise of the observations can be reduced by decreasing the noise bandwidth, but pattern information can be lost by using a bandwidth, which is too small. The trade-off between a small bandwidth and consequently less overall noise and the signal dynamics, caused by the fast robot motion, must be chosen carefully. At the end, an improvement in the pattern repeatability from 99.2 mm, using a hardware receiver, to 65.6 mm, using a software receiver with carefully chosen parameters, can be achieved.",
keywords = "Absolute Antennenkalibrierung, Codephasenzentrumskorrekturen, Group Delay Variations, Loop filter, Absolute antenna calibration, Code phase corrections, Group delay variation, Loop filter, Codephase center correction, Group delay variations",
author = "Yannick Breva and Johannes Kr{\"o}ger and Tobias Kersten and Steffen Sch{\"o}n",
note = "Publisher Copyright: {\textcopyright} The Author(s) 2023.",
year = "2024",
doi = "10.1007/1345_2023_206",
language = "English",
isbn = "9783031638541",
series = "International Association of Geodesy Symposia",
publisher = "Springer Nature",
pages = "101--108",
editor = "Freymueller, {Jeffrey T.} and Laura S{\'a}nchez",
booktitle = "Gravity, Positioning and Reference Frames - Proceedings of the IAG Symposia - GGHS2022",
address = "United States",
}